Pathogen-Imprinted Polymer Film Integrated probe/Ti3C2Tx MXenes Electrochemical Sensor for Highly Sensitive Determination of Listeria Monocytogenes

Article information

J. Electrochem. Sci. Technol. 2022;13(4):431-437
Publication date (electronic) : 2022 July 15
doi : https://doi.org/10.33961/jecst.2022.00269
School of Materials & Enviromental Engineering, Shenzhen Polytechnic, Shenzhen 518055, PR China
*E-mail address: jiangxgiaohua1006@yeah.net
Received 2022 April 8; Accepted 2022 June 10.

Abstract

As one of the most hazardous and deadliest pathogens, Listeria monocytogenes (LM) posed various serious diseases to the human being, thus designing effective strategy for its detection is of great significance. In this work, by preparing Ti3C2Tx MXenes nanoribbon (Ti3C2TxR) as carrier and selecting thionine (Th) acted simultaneously as signal probe and functional monomer, a LM pathogen-imprinted polymers (PIP) integrated probe electrochemical sensor was design to monitor LM for the first time, that was carried out through the electropolymerization of Th on the Ti3C2TxR/GCE surface in the existence of LM. Upon eluting the templates from the LM imprinted cavities, the fabricated PIP/Ti3C2TxR/GCE sensor can rebound LM cells effectively. By recording the peak current of Th as the response signal, it can be weakened when LM cell was re-bound to the LM imprinted cavity on PIP/Ti3C2TxR/GCE, and the absolute values of peak current change increase with the increasement of LM concentrations. After optimizing three key parameters, a considerable low analytical limit (2 CFU mL−1) and wide linearity (10–108 CFU mL−1) for LM were achieved. In addition, the experiments demonstrated that the PIP/Ti3C2TxR sensor offers satisfactory selectivity, reproducibility and stability.

1. Introduction

Listeria monocytogenes (LM) is a foodborne pathogen that widely exits in water, soil, plants, feces, and it can arouse several diseases, including abortion, meningitis and septicemia, to the humans with high morbidity and fatality rate by contaminating various food [14]. Owing to its great endanger, LM was listed as one of the most hazardous and deadliest pathogens [5,6]. Consequently, there have been several interesting electrochemical sensors, such as DNA-based sensor [3], sandwich immunosensor sensor [5,7] and peptide-based sensor [4], developed for the detection of LM since the electrochemical method is simpler, more sensitive, easy to operate, time-saving and low-cost compared to the other methods [810]. There’s no doubt that these sensors have considerably great applications, while the requirement of DNA, antibody, or aptamer endows the sensing processes with complex operation and high cost [11].

Molecularly imprinted polymer (MIP) is a tailor-synthesized receptor that can display specific and complementary recognition sites towards the related templates [1215]. Compared to the other receptors including antibodies, DNA and aptamers, MIP has several unique superiorities, such as cost-effective, high stability and simple preparation [1618]. Over the past decades, MIP has been confirmed to show great application values in the detection of protein, virus, and many organic molecules [1921]. In recent years, there are several MIP-like sensors developed for pathogen detection [22,23], this inspired us that it may be a perfect proposal to design a MIP-like electrochemical sensor for LM detection.

Selection of optimal carrier in preparing MIP is very important for the improvement of sensitivity. MXene, discovered and studied extensively in 2011, is a newly emerging transition metal carbide and/or nitride material and has been widely in various fields such as energy conversion and storage, field effect transistors and separation catalysis [2428] as well as microbial electrochemical systems [2932]. The general formula for MXene is Mn+1XnTx (e.g., Ti3C2Tx), where M denotes early transition metal and X represents carbon or nitrogen, while Tx refers surface functional groups (e.g., -OH, -O, -F) [3337]. Because of its huge specific active area, good conductivity and mechanical properties, MXene has great application prospects as a promising electrode material for electrochemical sensors [3841]. As for the MIP synthesization, there are several approaches, including electrochemical polymerization, thermal, and optical methods, have been proposed, among which, the first method has attached the most considerable attentions since it offers a very simple and controllable modification of the polymer to the electrode surface [4245]. Therefore, the utilization of suitable electroactive functional monomers is another key step for the preparation of MIP-based sensor. Thionine (Th), an aromatic dye with two amino groups, has demonstrated to be a desirable candidate as a promising functional monomer since its electropolymerization can generate a poly(thionine) film with superior electron transfer capability, and it can also be served as a signal molecule with good stability and electrochemical response [46,47].

Based on the above statements, in this work, a highly sensitive MIP-like (pathogen imprinted polymer, PIP) integrated probe electrochemical sensor was proposed for LM detection by preparing Ti3C2Tx MXenes nanoribbon (Ti3C2TxR) as the carrier of PIP and using Th acted simultaneously as the functional monomer and signal probe (Scheme 1). After optimizing three key experimental factors, a considerably low analytical limit and wide linearity of LM were obtained. This work offers a simple and low-cost pathway for the electrochemical detection of LM.

Scheme 1

Illustrations for the construction of PIP/Ti3C2TxR/GCE sensor and re-bounding LM

2. Experimental

2.1 Preparation of Ti3C2TxR

Ti3C2TxR was prepared according to the previous works with similar modification [48]. In brief, 1.0 g Ti3AlC2 was added into 30.0 mL hydrofluoric acid solution and stirred gently at 40°C to form Ti3C2Tx nanosheets (Ti3C2TxS) that can be collected after centrifugation and washed with water. Next, the obtained Ti3C2TxS powder of 0.2 g was mixed with 25.0 mL KOH solution (6.0 M) and further stirred under N2 atmosphere at 25°C for four days, thus resulting the information of Ti3C2TxR.

2.2 Construction of PIP sensor

Firstly, 2.0 mg Ti3C2TxR powders were dispersed into 4.0 mL water and treated for 10 min with ultrasound. Next, 6 μL of the produced Ti3C2TxR dispersion was dripped onto the GCE surface and dried with infrared lamp to form Ti3C2TxR/GCE. Then, the PIP sensor was prepared by electropolymerizing of 5.0 mM Th and LM on the Ti3C2TxR/GCE surface in 0.1 M PBS (pH 6.0) for 20 cycles with the potential range from −0.4 to 0.4 V at a scan rate of 50.0 mV/s. Afterwards, the polymer modified electrode was soaked in 0.5 M hydrochloric acid solution to remove the LM template, which was labeled as PIP/ Ti3C2TxR/GCE. As a comparison, non-pathogen imprinted polymer (NIP) modified Ti3C2TxR/GCE (NIP/Ti3C2TxR/GCE) was constructed with the similar processes just in the inexistence of LM.

2.3 Detection of LM

Firstly, PIP/Ti3C2TxR/GCE was incubated in LM solution with different concentrations for 20 min to recognize and capture LM, denoting the formed electrode as LM-PIP/Ti3C2TxR/GCE. Next, the differential pulse voltammetry (DPV) test was carried out in 0.1 M PBS (pH 6.0). The absolute value of peak current difference (|ΔIp|) was recorded and calculated according to the following equation:

|ΔIp|=|Ip0-Ip|

where Ip0 represents the peak current of PIP/ Ti3C2TxR/GCE, while Ip denotes the peak current of LM-PIP/Ti3C2TxR/GCE.

3. Results and Discussion

3.1 Characterization of Ti3C2TxR

The preparation of Ti3C2TxR was investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). As show in Fig. 1a, the purchased Ti3AlC2 exhibits a closely aligned structure. After etching Ti3AlC2 with hydrofluoric acid, the loosely 2D layered structure can be observed obviously for the formed Ti3C2TxS (Fig. 1b). From the SEM image (Fig. 1c) and TEM image (Fig. 1d) of Ti3C2TxR, it can be found that the nanoribbon structure was obtained for Ti3C2TxR, and the average diameter is about 35 nm, indicating that Ti3C2TxR was produced successfully.

Fig. 1

The SEM images of (a) Ti3AlC2, (b) Ti3C2TxS and (c) Ti3C2TxR; (d) the TEM image of Ti3C2TxR

3.2 Electrochemical studies of PIP sensor

Firstly, the imprinted process of PIP sensor was studied by electrochemical impedance spectroscopy (EIS). As shown in Fig. 2, it displayed the Nyquist diagrams of various electrodes in the solution of 2.0 mM [Fe(CN)6]3−/[Fe(CN)6]4−. Before the removal of LM template, the modified electrode shows a remarkable interfacial resistance, revealing that the presence of LM has larger obstruction to decrease the electron transfer rate and increase the resistance of the electron flow. However, when the LM template was removed from the imprinted cavities, an obvious reduction of interfacial resistance could be found at PIP/Ti3C2TxR/GCE. The reason is that there are a large number of imprinted cavities produced on the electrode surface through the elution of LM template, which increases the diffusion rate of [Fe(CN)6]3−/4− via the PIP film and makes it easier to transfer electron. The impedance changes of the modified procedures also suggested that the PIP sensor has been constructed successfully. Furthermore, after the incubation of PIP/Ti3C2TxR/GCE in the LM solution, an increased impedance can be observed at LM-PIP/ Ti3C2TxR/GCE, this can be attributed to the rebound LM cell in imprinted cavities that can block the channel of [Fe(CN)6]3−/4− to the electrode surface.

Fig. 2

The EIS plots of PIP/Ti3C2TxR/GCE (a) before and (b) after the removal of LM template, and (c) LM-PIP/ Ti3C2TxR/GCE

Next, the feasibility of PIP sensor towards LM detection was evaluated by DPV since it can exhibit high sensitivity and resolution. As exhibited in Fig. 3, before the removal of LM template, the as-prepared PIP electrode possesses a weak peak current of Th at ~−0.2 V; along with the LM elution from the electrode surface, the formed imprinted cavities in the polymer layer can generate many electron transmission channels, leading to an increased obviously oxidation signal of Th. Whereas with the incubation of PIP/Ti3C2TxR/GCE in LM solution (103 CFU mL−1), the rebound LM cell into the imprinted cavities can impede the electron channel for Th, thus leading to the decrease of Th signal current. As for NIP/ Ti3C2TxR/GCE, there is nearly no difference observed before and after its incubation in LM solution that is because NIP/Ti3C2TxR/GCE cannot recognize and bound LM cells due to the inexistence of LM imprinted cavities. These results proved the designed detection strategy for LM in this work is feasible

Fig. 3

DPV responses of PIP/Ti3C2TxR/GCE (a) before and (b) after the removal of LM template, and (c) LM-PIP/ Ti3C2TxR/GCE

Before the quantitative analysis of LM, several key parameters were optimized for obtaining the best analytical capability of the PIP sensor. As shown in Fig. S1–S3, the optimal conditions for the concentration of template LM, the polymerization cycles of Th and the incubation time of PIP/Ti3C2TxR/GCE in LM solution were 2×107 CFU mL−1, 18 and 25 min, respectively. Then, under the optimal conditions, DPV was used to monitor the concentration of LM in pH 6.0 PBS. Fig. 4a displayed the DPV responses of LM with various concentrations at PIP/Ti3C2TxR/ GCE. It can be found with the increase of LM concentrations, the peak signals of Th gradually decrease owing to the blocking of the imprinted cavities, and the |ΔIp| values are linear with LM concentrations in a range from 10 to 108 CFU mL−1. The corresponding linear regression equation is |ΔIp| (μA) = 0.3714 + 3.706 Log C (R = 0.9984) and the limit of detection (LOD) was obtained to be 2 CFU mL−1 (S/N = 3) (Fig. 4b I). For comparison, NIP/Ti3C2TxR/GCE was used also to monitor LM. As shown in Fig. 4b II, in contrast to PIP/Ti3C2TxR/GCE, there is almost no change for the |ΔIp| values with different concentrations of LM, revealing that NIP/Ti3C2TxR/GCE can’t bound LM cells due to the lack of specific cavity. Especially, compared to the previous studies (Table 1), the present constructed PIP sensor exhibits a preferable analytical capability with a relatively lower LOD and wider linearity, allowing the highly effective determination of LM.

Fig. 4

(a) The DPV responses of LM at different concentrations from 0 to 108 CFU mL−1 on PIP/Ti3C2TxR/GCE; (b) the linear relationships for LM detection based on (I) PIP/Ti3C2TxR/GCE and (II) NIP/Ti3C2TxR/GCE

Comparisons between the present PIP senor and previous electrochemical sensors for LM

To study the selectivity of the PIP sensor, the asprepared PIP/Ti3C2TxR/GCE was used to detect LM and other interfering pathogens including Escherichia (Es), Vibrio parahaemolyticus (VP), Staphylococcus aureus (SA), Shigella (Sh), and Salmonella enteriditis (SE). Fig. 5 displays the |ΔIp| values of PIP/Ti3C2TxR/GCE towards LM and other pathogens at the same concentration (104 CFU mL−1) in 0.1 M PBS (pH 6.0), and the experiments were carried out in triplicate. The results reveal that the presence of LM can cause a significant change (|ΔIp|) in the peak current, while almost no |ΔIp| values were observed for the other pathogens (less than 6.0%). In view of the fact that one sample may contain multiple pathogens in real situation, so the DPV responses of LM in the standard solutions containing other interfering pathogens were studied further. The results reveal the current responses did not change significantly with the |ΔIp| values ranging from 13.78 to 14.62 μA, indicating that of the established PIP sensor exhibits satisfactory selectivity.

Fig. 5

Selectivity of established PIP sensor toward LM. The concentration for each pathogens is 104 CFU mL−1

Another two significant indicators for sensor performances are reproducibility and stability. For evaluating the reproducibility of PIP sensor, eight parallel-fabricated PIP/Ti3C2TxR/GCE were applied to record the DPV response of 104 CFU mL−1 LM. As showed in Fig. S4a, it can be found that the RSD value of |ΔIp| is only 3.65%, indicating that the asprepared PIP/Ti3C2TxR/GCE offers desirable reproducibility. In addition, the storage stability of the fabricated PIP sensor was investigated through comparing the mean |ΔIp| value using the stored PIP/ Ti3C2TxR/GCE (4°C for 28 d) with those of fabricated freshly ones (Fig. S4b). The results show that the PIP sensor can retain 93.2% of its initial signal, revealing a long lifetime for the fabricated sensor.

4. Conclusions

In this study, a pathogen imprinted film fabricated on a Ti3C2TxR modified electrode was developed for the first time for the highly effective determination of LM. In strategical, the introduced Th cannot only act as an effective functional monomer, but also can dedicate as an internal reference probe of the PIP sensing platform. In addition, Ti3C2TxR can offer a desirable carrier with large specific active area and good conductivity. By virtue of the optimal experimental conditions, the fabricated PIP/Ti3C2TxR/GCE sensor displayed a low LOD (10–108 CFU mL−1), wide linearity (2 CFU mL−1), high selectivity, excellent repeatability and stability. This sensitive, simple, and selective sensing strategy for LM opens a new horizon for its sensitive and rapid recognition, which also holds great promise for the future applications to other pathogens.

Supporting Information

Acknowledgment

Financial support from the Key project of Shenzhen Polytechnic (No.6020310004K) is gratefully acknowledged.

References

1. Silva N.F.D, Neves M.M.P.S, Magalhães J.M.C.S, Freire C, Delerue-Matos C. Trends Food Sci. Technol 2020;99:621–633.
2. Ding J, Lei J, Ma X, Gong J, Qin W. Anal. Chem 2014;86(19):9412–9416.
3. Qi X, Wang Z, Lu R, Liu J, Li Y, Chen Y. Food Chem 2021;338:127837.
4. Eissa S, Zourob M. Microchim. Acta 2020;187:486.
5. Cheng C, Peng Y, Bai J, Zhang X, Liu Y, Fan X, Ning B, Gao Z. Sens. Actuators B Chem 2014;190:900–906.
6. Chen Q, Lin J, Gan C, Wang Y, Wang D, Xiong Y, Lai W, Li Y, Wang M. Biosens. Bioelectron 2015;74:504–511.
7. Jiang X, Ding W, Lv Z, Rao C. Anal. Sci 2021;37(12):1701–1706.
8. Niu X, Zheng W, Yin C, Weng W, Li G, Sun W, Men Y. J. Electroanal. Chem 2017;806:116–122.
9. Liu A, Shen L, Zeng Z, Sun M, Liu Y, Liu S, Li C, Wang X. Food Anal. Methods 2018;11:215–223.
10. Silva N.F.D, Neves M.M.P.S, Magalhães J.M.C.S, Freire C, Delerue-Matos C. Talanta 2020;216:120976.
11. Riu J, Giussani B. TrAC - Trends Anal. Chem 2020;126:115863.
12. Sarabaegi M, Roushani M. Microchem. J 2021;168:106388.
13. Sarabaegi M, Roushani M, Hosseini H. Talanta 2021;223:121700.
14. Roushani M, Jalilian Z. Electroanalysis 2018;30(11):2712–2718.
15. Jafari M.T, Rezaei B, Bahrami H. Anal. Sci 2018;34(3):297–303.
16. Chen S, Chen X, Zhang L, Gao J, Ma Q. ACS Appl. Mater. Interfaces 2017;9(6):5430–5436.
17. Wang R, Wang L, Yan J, Luan D, Sun T, Wu J, Bian X. Talanta 2021;226:122135.
18. Ghanbari K, Roushani M. Sens. Actuators B Chem 2018;258:1066–1071.
19. Cao Y, Feng T, Xu J, Xue C. Biosens. Bioelectron 2019;141:111447.
20. Mugo S.M, Lu W, Dhanjai D. Med. Devices Sens 2020;3(2):e10071.
21. Roushani M, Sarabaegi M, Rostamzad A. J. Iran. Chem. Soc 2020;17:2407–2413.
22. Tokonami S, Nakadoi Y, Takahashi M, Ikemizu M, Kadoma T, Saimatsu K, Dung L.Q, Shiigi H, Nagaoka T. Anal. Chem 2013;85(10):4925–4929.
23. Golabi M, Kuralay F, Jager E.W, Beni V, Turner A.P. Biosens. Bioelectron 2017;93:87–93.
24. Sinha A, DhanjaiZhao H, Huang Y, Lu X, Chen J, Jain R. TrAC - Trends Anal. Chem 2018;105:424–435.
25. Zhang Y, Jiang X, Zhang J, Zhang H, Li Y. Biosens. Bioelectron 2019;130:315–321.
26. Tu X, Gao F, Ma X, Zou J, Yu Y, Li M, Qu F, Huang X, Lu L. J. Hazard. Mater 2020;396:122776.
27. Kalambate P.K, Gadhari N.S, Li X, Rao Z, Navale S.T, Shen Y, Patil V.R, Huang Y. TrAC - Trends Anal. Chem 2019;120:115643.
28. Yi Y, Ma Y, Ai F, Xia Y, Lin H, Zhu G. Chem. Commun 2021;57(63):7790–7793.
29. Pawar A.A, Karthic A, Lee S, Pandit S, Jung S.P. Environ. Eng. Res 2022;27(1):200484.
30. Son S, Koo B, Chai H, Tran H.V.H, Pandit S, Jung S.P. J. Water Process Eng 2021;40:101844.
31. Zahid M, Savla N, Pandit S, Thakur V.K, Jung S.P, Gupta P.K, Prasad R, Marsili E. Desalination 2022;521:115381.
32. Kang H, Kim E, Jung S.P. Int. J. Hydrog. Energy 2017;42(45):27685–27692.
33. Xia Y, Ma Y, Wu Y, Yi Y, Lin H, Zhu G. Microchim. Acta 2021;188:377.
34. Xia Y, Zhao Y, Ai F, Yi Y, Liu T, Lin H, Zhu G. J. Hazard. Mater 2022;425:127974.
35. Sharifuzzaman M, Barman S.C, Zahed M.A, Sharma S, Yoon H, Nah J.S, Kim H, Park J.Y. Small 2020;16(46):2002517.
36. Yao Y, Lan L, Liu X, Ying Y, Ping J. Biosens. Bioelectron 2020;148:111799.
37. Yi Y, Zhao Y, Zhang Z, Wu Y, Zhu G. Trends Environ. Anal. Chem 2022;33:e00152.
38. Ma X, Tu X, Gao F, Xie Y, Huang X, Fernandez C, Qu F, Liu G, Lu L, Yu Y. Sens. Actuators B Chem 2020;309:127815.
39. Xia Y, Li J, Zhu G, Yi Y. Sens. Actuators B Chem 2022;355:131247.
40. Xie Y, Gao F, Tu X, Ma X, Xu Q, Dai R, Huang X, Yu Y, Lu L. J. Electrochem. Soc 2019;166(16):B1673.
41. Xu Q, Xu J, Jia H, Tian Q, Liu P, Chen S, Cai Y, Lu X, Duan X, Lu L. J. Electroanal. Chem 2020;860:113869.
42. Panasyuk T.L, Mirsky V.M, Piletsky S.A, Wolfbeis O.S. Anal. Chem 1999;71(20):4609–4613.
43. Ellis T.K, Galerne M, Armao J.J IV, Osypenko A, Martel D, Maaloum M, Fuks G, Gavat O, Moulin E, Giuseppone N. Angew. Chem. Int. Ed 2018;57(48):15749–15753.
44. Yi Y, Zhang D, Ma Y, Wu X, Zhu G. Anal. Chem 2019;91:2908–2915.
45. Han H, Zheng H, Li B, Xiang H, Zhangluo Y. Indian J. Chem. Technol 2017;56A(05):501–507.
46. Huang Q, Zhao Z, Nie D, Jiang K, Guo W, Fan K, Zhang Z, Meng J, Wu Y, Han Z. Anal. chem 2019;91(6):4116–4123.
47. Dai Y, Kan X. Chem. Commun 2017;53(86):11755–11758.
48. He X, Jin S, Miao L, Cai Y, Hou Y, Li H, Zhang K, Yan Z, Chen J. Angew. Chem. Int. Ed 2020;59(38):16705–16711.
49. Wang D, Chen Q, Huo H, Bai S, Cai G, Lai W, Lin J. Food Control 2017;73:555–561.
50. Davis D, Guo X, Musavi L, Lin C.-S, Chen S.-H, Wu V.C. Ind. Biotechnol 2013;9(1):31–36.
51. Lu Y, Liu Y, Zhao Y, Li W, Qiu L, Li L. J. Nanomater 2016;2016:3895920.

Article information Continued

Fig. 1

The SEM images of (a) Ti3AlC2, (b) Ti3C2TxS and (c) Ti3C2TxR; (d) the TEM image of Ti3C2TxR

Fig. 2

The EIS plots of PIP/Ti3C2TxR/GCE (a) before and (b) after the removal of LM template, and (c) LM-PIP/ Ti3C2TxR/GCE

Fig. 3

DPV responses of PIP/Ti3C2TxR/GCE (a) before and (b) after the removal of LM template, and (c) LM-PIP/ Ti3C2TxR/GCE

Fig. 4

(a) The DPV responses of LM at different concentrations from 0 to 108 CFU mL−1 on PIP/Ti3C2TxR/GCE; (b) the linear relationships for LM detection based on (I) PIP/Ti3C2TxR/GCE and (II) NIP/Ti3C2TxR/GCE

Fig. 5

Selectivity of established PIP sensor toward LM. The concentration for each pathogens is 104 CFU mL−1

Scheme 1

Illustrations for the construction of PIP/Ti3C2TxR/GCE sensor and re-bounding LM

Table 1

Comparisons between the present PIP senor and previous electrochemical sensors for LM

Sensors Linearity (CFU mL1) LODs (CFU mL1) References
Peptides/gold-carbon 10–107 9 [4]
Gold electrode 102–106 102 [5]
Interdigitated array microelectrode 1.9×103–1.9×106 1.6×103 [49]
Gold nanoparticles/screen-printed carbon electrode 2.25×10–2.25×105 2.25×102 [50]
Carbon nanotube fibers electrode 102–105 1.07×102 [51]
PIP/Ti3C2TxR/GCE 10–108 2 This work